The engine badge on an E70 X5 matters more than the year, the trim or the mileage. Owners on Xoutpost describe the 2007-2010 3.0si and xDrive30i as solid, the 2011-2013 xDrive35i as the sensible pick, and the xDrive50i with the original N63 V8 as a car you buy only with proof of expensive work already done. One 50i owner in a long-term reliability thread reported roughly $15,000 in maintenance in a single year.
Same body. Same interior. Four very different bills.
This guide covers the E70 generation, built from mid-2006 through July 2013 and sold in the US as 2007 to 2013 models. NHTSA's per-vehicle index lists between 6 and 14 recall campaigns for each model year, and many of those are passenger air bag inflator campaigns that touch almost every car. Read the engine sections first. Then check the year table and the inspection list before you test drive anything.
This Generation at a Glance
The E70 is the second-generation X5. It replaced the E53 and ran until the F15 arrived for 2014. BMW built it in Greer, South Carolina. The 2011 model year brought a mid-cycle refresh (BMW calls it the LCI): revised bumpers, headlights and taillights, a newer infotainment system, and a switch to all-turbo gasoline engines with an eight-speed automatic. The diesel and the X5 M kept their six-speed gearboxes.
| Powertrain | Years | Output | Transmission | EPA combined MPG |
|---|---|---|---|---|
| 3.0L N52 inline-six (3.0si, xDrive30i) | 2007-2010 | about 260-270 hp | 6-speed | 18 |
| 4.8L N62 V8 (4.8i, xDrive48i) | 2007-2010 | about 350 hp | 6-speed | 16 |
| 3.0L N55 turbo inline-six (xDrive35i) | 2011-2013 | about 300 hp | 8-speed | 19 |
| 4.4L N63 twin-turbo V8 (xDrive50i) | 2011-2013 | about 400 hp | 8-speed | 16 |
| 3.0L diesel inline-six (xDrive35d) | 2009-2013 | about 265 hp, 425 lb-ft | 6-speed | 21-22 |
| 4.4L S63 twin-turbo V8 (X5 M) | 2010-2013 | about 550 hp | 6-speed | 14 |
Output figures are rounded from published spec sheets, which disagree by a few horsepower. MPG comes from EPA ratings on fueleconomy.gov for the 2008, 2009, 2010 and 2012 model years.
Current pricing and inventory: BMW X5 market data.
Powertrain & Trim Breakdown
3.0L N52 inline-six (2007-2010)
The N52 is the naturally aspirated six in the 3.0si and xDrive30i. Forum consensus calls it the most dependable gasoline E70 engine. Its weak spot is cooling. The electric water pump and thermostat fail without much warning, and the oil filter housing gasket and valve cover leak with age. Budget for both before you trust the car.
Owners in a Xoutpost N52 thread listed ignition coils at roughly 60,000 to 105,000 miles, VANOS solenoid work between 75,000 and 170,000 miles, the oil filter housing gasket near 110,000 miles, and plastic coolant hoses at 125,000 to 175,000 miles. One 2007 owner reported a third water pump and thermostat in three years and put cooling-system parts at $700 to $800 a year.
NHTSA campaign 23V707 covers aluminum VANOS bolts that can loosen and break on certain 2010-2012 BMW models including the X5 xDrive30i. A broken bolt can stall the engine. Ask a dealer to confirm it on the VIN. NHTSA's index lists it for the 2010 and 2011 X5.
Some owners say the 3.0si struggles with the X5's weight. Others call it fine. It is slower than the turbo cars, and EPA rates it at 18 combined.
3.0L N55 turbo inline-six (2011-2013)
The xDrive35i uses the N55, a single twin-scroll turbo six paired with the eight-speed automatic. Owners on Xoutpost often pick it as the best E70 gas engine. The recurring complaints are the electric water pump, oil leaks from the filter housing and valve cover, and the high-pressure fuel pump.
A water pump, thermostat and expansion tank job runs about $1,000 to $1,500 according to OpenLabor's estimate. Owners expect to replace the pump every 60,000 to 80,000 miles. A high-pressure fuel pump failure runs about $1,050 on one dealer quote in a Xoutpost thread, and OpenLabor estimates $1,200 to $2,000. That owner's symptoms were long crank times, then a reduced-power warning, under 80,000 miles. The dealer said no recall applied to the 2011 N55.
Several owners also point to carbon buildup on the intake valves of any direct-injected engine. Walnut blasting is the usual fix, typically after 60,000 miles or when performance drops.
NHTSA campaign 12V019 covers 2012 xDrive35i vehicles built in a three-day window in December 2011, where the transmission's park lock may not engage. It is narrow. Check the VIN, but expect most cars to be outside it.
4.8L N62 V8 (2007-2010)
The 4.8i and xDrive48i use the older naturally aspirated N62 V8. It tows well and sounds good. It also leaks. Owners report valve stem seals, valve cover and upper timing cover gaskets, and coolant valley pipe O-rings as the standard failure chain.
One owner in the "time to cut bait" thread bought a 2009 4.8i at 47,000 miles. By 79,000 miles he had spent about $3,400 at an independent shop on an oil leak that started at the alternator bracket. A coolant valley pipe leak then added about $2,500, including a water pump and thermostat. He valued the truck at $10,000 to $12,000. Labor, not parts, drives these bills.
Owners warn that the N62 is cheap only if you do the work yourself. Several advise against it for anyone paying a shop. Fuel economy is also poor: EPA rates it at 16 combined, and one owner reports about 12.5 mpg with aggressive driving.
NHTSA campaign 17V683 covers a crankcase ventilation (PCV) valve heater that can short and cause a fire on certain 2007-2011 BMW models including the X5 xDrive30i. The recall text lists the xDrive30i, not the V8 X5. Verify any V8 car against its own VIN rather than assuming.
4.4L N63 twin-turbo V8 (xDrive50i, 2011-2013)
The original N63 is the most criticized engine in the E70 lineup. Forum posts describe heavy oil consumption, valve stem seal wear, fuel injector failures, turbo coolant line leaks, auxiliary coolant pump failures and timing chain wear. BMW issued a Customer Care Package under service bulletin B001314 for N63 cars, covering injectors, a timing chain inspection and other items. It is not a recall.
One owner in a Xoutpost customer care thread had a worn chain replaced at about 38,000 miles, a repair that required pulling the engine for two to three weeks. In the long-term reliability thread, one owner said a valve stem seal repair alone was about $10,000 at dealer rates. A commenter knew owners who needed three or four sets of injectors even after the package.
Not every owner has a bad story. Some posters say they know plenty of 50i owners past 75,000 miles with no major problems. A Leasehackr poster called the N63 one of the most problematic engines in recent years. The honest summary is a lottery with a very expensive losing ticket. Buy only with documentation that the injectors, valve stem seals and timing chain inspection were done, and with a warranty you have read.
NHTSA campaigns 11V521 and 18V248 cover the electric auxiliary water pump circuit board overheating on certain turbocharged V8 BMWs, including the 2010-2011 and 2011-2012 X5 xDrive50i and X5 M. The risk is a fire. Dealers replace the pump at no charge. Ask for proof it was done.
3.0L diesel xDrive35d (2009-2013)
The 35d earns real love for torque and range. EPA rates it at 21 to 22 combined, the best of the lineup. Owners say the engine itself is reliable. The emissions hardware is not. Xoutpost owners cite NOx sensors, the diesel particulate filter, EGR parts, and the diesel exhaust fluid (DEF) and SCR injector valves as likely failures.
One poster put ownership at about $2,500 a year unless you wrench yourself. Another suggested budgeting for NOx sensor or DPF work within the first 200,000 miles. Water intrusion through a broken bulkhead partition damaged injectors on one car. The timing chain sits at the back of the engine, so replacing it means pulling the engine.
NHTSA campaign 18V336 covers 2009-2013 X5 xDrive35d vehicles where the engine idler pulley bolt may loosen and break, causing loss of power steering. Dealers replace the bolt with an improved part. One owner reported a bolt breaking again about 66,000 miles after the first repair, so ask for service records. Campaign 13V339 covers a fuel filter heater that can stay on and overheat on 2009-2010 xDrive35d cars built June 13 to November 9, 2009.
4.4L S63 twin-turbo V8 (X5 M, 2010-2013)
The X5 M has about 550 horsepower and EPA rates it at 14 combined. Buying guides flag cooling parts around the hot-V turbo layout, oil leaks and rod bearing wear, along with the usual E70 transfer case and air suspension risks. One parts aggregator lists a plastic turbo coolant fitting as a specific failure point. Treat any X5 M as a specialist purchase. Get a compression and leak-down test, a rod bearing history and a cooling pressure test before you pay a deposit.
NHTSA campaigns 11V521 and 18V248 apply here too. So does 10V152, which covers 2010 X5 M exterior lighting compliance.
Shared hardware: transfer case, air suspension and driveshaft
The xDrive transfer case is a known E70 weak point. One owner in a Xoutpost thread had a 2008 4.8i fail at about 160,000 miles with a clicking sound at low speed. Parts were quoted at about $2,800 for the case and nearly $1,000 for the front driveshaft. A rebuilt case and front axle shipped to a rebuilder cost about $2,700 total. Sources suggest regular differential and transfer case fluid changes.
Rear air suspension is optional on many cars. Owners say the rear air springs leak as they age, and the car sags overnight when they do. YouCanic says repairs can spiral into the thousands. Conversion kits to coil springs cost around $300 before fitting. Several Xoutpost owners say skip the air suspension when you shop.
Two front driveshaft recalls matter on 2011 and later cars. NHTSA campaign 16V311 covers certain 2011 X5s built April to November 2010. Campaign 17V138 covers 2011-2013 xDrive35i, xDrive50i, X5 M and xDrive35d cars. Both concern a front universal joint that lets water in, and dealers replace the front driveshaft at no charge.
Trim Levels
The E70 sold mostly by engine badge, then by option package. There is no clean trim ladder, so shop by powertrain first.
| Trim or package | Key equipment | What to pay extra for |
|---|---|---|
| 3.0si / xDrive30i | N52 inline-six, six-speed | Best gas reliability record, if cooling work is documented |
| 4.8i / xDrive48i | N62 V8 | Only with leak repairs done and receipts |
| xDrive35i | N55 turbo six, eight-speed | The sensible pick; pay for proof of water pump and fuel pump work |
| xDrive50i | N63 twin-turbo V8 | Only with documented injector, valve seal and chain work |
| xDrive35d | Diesel six, DEF system | Clean emissions history and the idler pulley bolt recall |
| X5 M | S63 V8, M suspension | Specialist inspection and full cooling records |
| Sport package (2008-2009) | Sport seats and Adaptive Drive | A good pick per some owners |
| M Performance package (2013) | Sport suspension, wider fenders, more output | Adds about 15 hp on the 35i and 40 hp on the 50i |
| Air suspension, camera, navigation, head-up display | Comfort and tech | Skip if you can. Owners say they add repair complexity |
Owners on Xoutpost repeatedly say to skip the cameras, navigation, head-up display and active seats on high-mileage cars, because each adds a repair. The older CCC navigation is slow and has no map updates after 2015. A third-row seat and panoramic roof are also options. Check that every sunroof panel moves, because one owner reported a 2012 twin sunroof jamming with a repair estimate over $2,000.
Which Model Years to Target Within This Gen
The counts below come from NHTSA's per-vehicle recall index for the X5, as of November 2026. They are campaigns the index lists for each model year, not campaigns that actually apply to every car. Many are air bag inflator campaigns that apply by VIN and registration region.
| Year | NHTSA campaigns | Key changes | Verdict |
|---|---|---|---|
| 2007 | 8 | Launch year, 3.0si and 4.8i | Caution. First-year bugs, old electronics |
| 2008 | 10 | Same engines. Fuel pump campaign 10V518 on six-cylinder cars | Caution |
| 2009 | 12 | xDrive30i, xDrive48i, and the new 35d diesel | Fair. Check diesel recalls |
| 2010 | 14 | Last N52 and N62 year. X5 M debuts | Good for the 30i. Last pre-refresh year |
| 2011 | 14 | Refresh, N55 and N63, eight-speed | Good with an N55 |
| 2012 | 10 | 35i steady, 50i carries N63 risk | Best value with an N55 |
| 2013 | 6 | Final year, M Performance package | Best overall if you want an N55 and have the records |
The 2012 and 2013 xDrive35i are the cleanest buys. They have the refreshed interior, the eight-speed and the N55. Owners rank 2011 to 2013 as the target years for the 35i if you can accept a water pump replacement. If you want a naturally aspirated engine and the smoother cabin, a low-mileage 2010 xDrive30i with cooling work done is a defensible alternative.
Avoid a 2007 unless the price reflects it. Owners call it a first-year car with fewer options. Avoid any 50i without paperwork.
Pre-Purchase Inspection Checklist
Run every VIN through the recall lookup before you drive. Passenger air bag inflator campaigns 16V364, 17V020, 18V030, 19V017 and 20V016 apply to many E70 X5s by region. NHTSA's text for 18V030, 19V017 and 20V016 says owners should not drive the vehicle until the remedy is performed. Confirm the remedy on the exact VIN.
All cars
- Check ride height after the car sits overnight. A sagging rear means air spring or compressor trouble.
- Drive with the wheels turned at low speed. Clicking, shuddering or a drivetrain warning points to the transfer case.
- Ask for the date of the last differential and transfer case fluid service. Parkers says to look for it after 40,000 miles.
- Test every sunroof panel, window and power seat. These parts are costly out of warranty.
- Look under the car for fresh oil at the filter housing, valve cover and oil pan.
N52 and N55 cars
- Ask for water pump and thermostat history. Walk away or price it in if the pump is original past 80,000 miles.
- Cold start the engine. Long crank times on an N55 point to the high-pressure fuel pump.
- Scan for fault codes and ask when ignition coils, spark plugs and the oil filter housing gasket were last done.
N62 and N63 cars
- Look for blue smoke on acceleration after idling. That points to valve stem seals.
- Ask for proof of the N63 Customer Care Package work, injector replacements and any timing chain inspection.
- Check the oil level the day you test drive, then again after. Heavy consumption is the warning sign.
- Inspect the coolant valley area for crust or dampness.
Diesel cars
- Confirm campaign 18V336 and its improved idler pulley bolt were done.
- Scan for DEF, NOx sensor and particulate filter codes.
- Check the DEF tank for leaks and ask when it was last filled.
Running Costs
| Powertrain | Combined MPG | Key maintenance items | Owner-reported annual cost |
|---|---|---|---|
| N52 | 18 | Water pump, thermostat, oil leaks | About $700-800/yr on cooling parts (one owner) |
| N55 | 19 | Water pump, high-pressure fuel pump, gaskets | About $1,000-2,000 per major job |
| N62 | 16 | Valve stem seals, valley pipe, timing cover | $3,400 plus $2,500 in one owner's case |
| N63 | 16 | Injectors, seals, chain, coolant lines | Five figures in worst cases |
| Diesel | 21-22 | NOx sensors, DPF, DEF system | About $2,500/yr (one poster) |
| S63 | 14 | Cooling, rod bearings, brakes | Specialist territory |
These are anecdotal figures from owner threads and parts-estimate sites, not a statistical average. The owner with the roughly $10,000 valve stem seal bill said an independent shop could have done the work for far less.
Expect premium fuel on every gas engine. Fluid changes for the transmission, differential and transfer case are cheap compared to the parts they protect.
FAQ
Is the BMW X5 E70 reliable? It depends on the engine. Owner forums rate the N52 and the N55 as the most dependable gasoline options. The N62 V8 leaks, the original N63 is the weak spot, and the diesel's emissions parts fail. Reliability here is a function of service records, not model year.
What E70 X5 year should I avoid? Avoid the 2007 unless the price reflects first-year risk. Owners call it a first-year car with older electronics. Avoid any 2011-2013 xDrive50i without proof of injector, valve seal and timing chain work. That engine drives most of the horror stories on Xoutpost.
Is the E70 X5 xDrive35i worth buying? Yes, with records. Owners on Xoutpost call the N55 xDrive35i the sensible E70, citing better handling of the vehicle's weight than the older six. Budget for the electric water pump and the high-pressure fuel pump, and look for oil leaks at the filter housing.
Is the E70 X5 diesel reliable? The diesel gets praise for torque and the best fuel economy in the lineup. Its emissions parts cause most of the trouble: NOx sensors, particulate filter, EGR and DEF injectors. Verify the idler pulley bolt recall, NHTSA campaign 18V336, was done, and budget about $2,500 a year.
How many miles does an E70 X5 last? Owners report E70s past 130,000 miles when the cooling system, fluid changes and oil leaks were handled on schedule. The question is repair cost, not whether the car runs. One 4.8i owner estimated about $9,000 in repairs over three years, which was a large share of the truck's value.
Bottom Line
Buy a 2011-2013 xDrive35i with a documented water pump and a clean fault scan. That car gives you the eight-speed, the refreshed interior and the engine owners trust most. If you want a naturally aspirated engine, a low-mileage 2010 xDrive30i with cooling records is the backup. Skip the 50i without paperwork and skip the 4.8i unless you wrench. Check every VIN against NHTSA, especially for the air bag inflator campaigns. Hunting one exact engine and year combination? CarScout checks dealer listings daily and emails new matches and price drops once a day.
Data sourced from NHTSA recall records, EPA fuel economy data on fueleconomy.gov, and owner discussions on Xoutpost's E70 forum, Leasehackr, plus YouCanic, Parkers, FCP Euro, Euro Premium Parts, OpenLabor, and Wikipedia. See the full BMW X5 market data for pricing and inventory.